John Boucher wrote:and not as whispered in certain circles that it wasn't done?
I am not suggesting it wasn't
but I would be inclined to share this information in the line of safty rather than remain silent
Hell Greg, what exactly are you saying or implying?
John you must be bored and wanting to stir the pot a bit?
let me elaborate for clarity...here is what Len said in a reply to john.com on page 1
J
ohn.com, The machine has been stripped to the frame, the frame has been sent to professionals for straightening if not true, thereafter it will go for full metallurgical non-destructive testing, better than X-ray (ultrasound/ultrasonic flaw detection). Should the frame be certified sound, then ALL load bearing bolts, mounts, brackets, bearings etc will be replaced or, if considered acceptable by the AP re-assembling the machine, refitted. A detailed inspection and run-out will be done on the head and if necessary a full head overhaul will take place. (My life is worth a hell of a lot more than the money or time it may cost).
Ok so lets consider that statement, ..you see the comments are suggesting the frame had a little ding? however I was told that the frame had more than a little ding?
In fact a certain Mr J Mc Harg (a student of len at the time) called louis Van Wyk (CFI & AP and AMO at FAFK) shortly after welding this frame?? to offer his welding services, should Van Wyk need them, as louis was re building his M16 at the time. Now the issue is that all welding work on airframes has to be done by an AP who is approved under part 66, was Mc Harg qualified??
So then add that fact the Mr Mc Harg who told louis Van Wyk he welded this frame we are discussing at his Facility, this would suggest without a doubt that the frame in question was not true? or do you think that is an unreasonable deduction?
In fact witnesses reported that the frame was substantially damaged? but that is conjecture. (on a side note Van Wyk scraped a M16 frame that in his opinion was not half as bad as the frame we are discussing, and purchased a new frame for his M16) this old frame is in my hanger if anyone wants to see it for comparison.
Now was Mr Mc Harg suitably qualified to weld on an aircraft frame? I dont know and Im not saying he is not? this is not the issue its just background.
Then while we are at it and since you have revived a thread from some 10 days ago (I was letting it slide because I have made my own arrangements for the damaged mast in my Xenon) I may as well add some depth to my comments.
You see chrome moly 4130 is not particularly difficult to weld, however if it is not cooled down correctly and if the area being welded is not warmed up correctly prior to welding the joint could suffer embrittlement, that is not noticeable to the naked eye.
If one were to take simple tests and apply strain on the welded area it will look like the weld joint is strong? however
we are not talking about the actual weld here, we are referring to the area around the weld, this is where stress fractures could occur from vibration and over time fatigue cracks can manifest, all invisible to the eye. (and if not noticed could contribute to a structural failure in flight)
These are the things we need to consider before embarking on just doing repairs to aircraft and we need to ask ourselves why are these regulations in place? ....they are to protect us from ourselves, (and despite some Pilots and enthusiast best attempts they are not qualified to make structural repairs to aircraft carrying fare paying passengers) and when it comes to aircraft being used for people who are paying then we need to be even more selective towards our maintenance and safty standards ...but I digress.
To come to your question, Im not implying anything and asked a simple question because I have suffered a mast failure in a new low hour aircraft and wanted to employ the services of a laboratory to annalise my mast crack and was hoping since Len has just declared he has recently had it done? and since len has won many awards (Flight safty as one of them) he would simply be able to furnish a name or a recommendation.
So John what exactly is your sudden interest in this matter? or are you setting me up to
ban me because I ask interesting questions.... or if you have the name and
place and a contact person who did the ND Testing on the frame will you share it for the world to see? saving me bandwidth and time to explain things that needed no further comment than just a company name and a contact person.
I have made contact with the CSIR locally and the cost involved in doing NDT will be uneconomical for a one off mast analysis? so am just wondering who Len used? because its not unreasonable to think he would spend more on a frame report than on a replacement frame from Butch?? so in short im not saying anything
In contrast I have just rebuilt a Xenon from the ground up and I could in a heartbeat furnish any interested party (friend or foe) with any information on parts or processes without any effort....because every part of the build I have done and have documented for all to see and Im not known for shortcuts when it comes to safty.
Read into this comment what you like.
Regards
Greg